Porsche
Special Tools 
USA Phone: (615) 735-3388
 How to Order.
Samstag Sales stocks a wide selection of German Made tools. On this page you will find items of interest to Porsche mechanics.  To make sure you are seeing the latest update, please hit reload on your browser. To see a picture of the tool, click on the price.  We can supply a limited selection of tools for Porsche as found on this page.
HOME Quick Search SEARCH
 eMail Samstag
How To Order
 Web Special
  Please Note: Our shopping cart is available for your convenience. The shipping is a flat rate calculated by value.   For more shipping options, email us with your shipping address and list of tools.
Last Porsche update: May13, 2013
.
How To
Search For a
Porsche Tool
 You can search for a Porsche tool on this page by using your web browser's find feature. For example, if you are using Netscape, you can click on Edit in the menu bar, then click on Find, and type in what you want to find.  A fast way to bring up the search dialog box is to type (CTRL) F. 
Quick Search

Brand & Number
Porsche Number
Description
Price
.
**************
 Advertising Special .12345678
HAZET
*
 HAZET Sticker. New Old Stock. With HAZET logo and wording  "LeMans Champions 1998 Porsche". Oval shape, 6 inches across. This one has some pin holes in the white border from being put on a bulletin board, but they are in the outside backing paper. HAZET is an Official Supplier to Porsche Motorsport. We only have this one!
Asking
$50.00
.************** . Axle Tools .
Matra 
VW 637/2
Special puller for front hub bearing grease cap. Adjustable jaw. For Porsche model 914 and 924. Also used on VW.
 
See
VW
Page
Kukko 70-2
Ball Bearing Extractor. Sold without arms.  Used with arms 70-722.

 See
Kukko
Page
Kukko 70-722
Set of 4 arms, 180mm in length each, 4 spacer rings good for bearing sizes: 6011 6012, 6206, 6207, 6304, 6306. Use with extractor 70-2.  Good for Bearing 6306 as found in rear axle on old Porsche 356.


 See
Kukko
Page
ST B 90-P2
Bonus Kit. 
3 parts with case.
*
 Sir Tools Bonus Kit. Wheel Bearing and Hub Removal and Installation Kit, for 911(non-turbo) 1974 and up, 924 and 944 from 1985 and up, 968, and Boxster. This is the Bonus Kit with 3 parts, B90-P2 bearing kit, B90-3 bracket, and B90-3J Horseshoe. Packed in a plastic storage case.  Pic 2.  Pic 3. Email or call (615) 735-3388 with your shipping address to order.
ST B 90-P3
Bonus Kit. 
3 parts with case.
*
 Sir Tools Bonus Kit. Wheel Bearing and Hub Removal and Installation Kit, for Porsche 911 Turbo 1990 and up & Porsche 928. This is the Bonus Kit with 3 parts, B90-P3 bearing kit, B90-3 bracket, and B90-3J Horseshoe. Packed in a plastic storage case. Pic 2.Pic 3. Email or call (615) 735-3388 with your shipping address to order.
.  . Belt Tools .
ST P208
*
 Pulley wrench. Needed for securing the generator from rotating during R&R of pulley or fan belt. Applicable: Model - 911,  year 1965-1974.
AMF
54973
 P208b Pulley wrench. Needed for securing the generator from rotating during replacement of the pulley or fan belt. Type 911, year 1975 and up.
. . Body Tools .
AMF 54924
9752
AMF  Pin Spanner for 911 Turbo (996) Spoiler. DIN1810B-34-36. Hook Wrench with pin, blued steel, for nuts with radial hole. For nut size range 34-36 mm. With 4mm pin. Overall length 170mm. The factory tool 9752 is an insert tool used with a torque wrench. This AMF tool will allow you to do the job, but you must be aware of the factory torque specifications. Please consult your service information.
Matra 3370
 * Pull hook for fuel filling pocket found on Panamera and Cayenne.
 See
VW
Page
Matra 3371
 * Body Panel Feeler Gauge
ST P243
*
 Super Duty Long Allen Socket -(8mm)
$ 34.95
ST P244
*
 Trailing Arm Height Adjuster
ST P245
*
 Mini Spanner Pin Wrench 
$ 23.94
ST P246
*
 Offset Flare Wrench
$ 49.95
. . Brake Tools .
KLANN
KL-0116-2 		*
 Klann Slide Hammer set consist of  jaw KL-0116-20 with 4.0 mm pins and jaw KL-0116-21 with 5.9 mm pins. Length 250mm, Weight 1.6 kg. This tool is used to remove stubborn brake pads. Special Order Only!

Matra
T10145
Sub for 
P83
 Brake Caliper Piston Spreader Tool. Type 356 / 911 / 912 / 914. This tool is used to force the brake caliper piston back to make room for the new brake pads. Good for Audi, BMW, Mercedes-Benz, Porsche, Volkswagen with disc brakes. Similar to KUKKO tool 126-00. Here is the tool that will allow you to do the job right. 


See VW
Page
KUKKO
126-01 
P86
 Brake pad puller. With 2 adjustable arms and 5mm pins.  Type 356, 911, 912, 924
See
KUKKO
Page
KUKKO
126-02		 P47 Brake Piston Clamp. For holding the brake calipers during repair on type 356.
See
KUKKO
Page
ST 1018 * Pressure Adapter needed for pressurizing the master cylinder or clutch slave cylinder reservoirs. Used in conjunction with a pressure bleeder. Equipped with a 1/4-18 NPT threaded opening. It is applicable on most every European model.
$33.95
(Picture)
Stahlwille
108-175x4		 *
 Parallel Pin Punch for brake safety pins. 4mm
$ 11.15
(Picture)
. . Camshaft Tools .
ST P204
*
 Chain Sprocket Holder needed for securing the chain sprocket and preventing chain slippage. This tool is extremely crucial when replacing tensioners or setting cam timing. Applicable: Model - 911, 930. 
ST P237
9191
 Sir Tools brand. Cam Bar is needed to secure the cam shaft from rotating during R&R of cam shaft nut. Crucial when adjusting valves or setting cam timing. Applicable: Model - 911, '89-'80
ST P253
*
 Cam securing fixture used for securing the intake and exhaust cam shafts in relation to each other during base timing, etc. Porsche models 996 through 2001 and Boxster up to 2004. Made by Sir Tools.
ST P260
 9612
9634
9611
9595
9595/1
 This exclusive cam master kit is specially assembled for the Master Porsche Technician, independent or otherwise. The kit consists of the factory correct tools
needed for Setting and Retaining cam timing during routine "on the car" maintenance of 996 engines up through 2001 and Boxster engines up through 2002.
Sir Tools offers this fully equipped master kit with all of the tools necessary for complete and simultaneous security of both the left and right side of the engine.
P 253 = Bar for setting cam timing.
P 255 = Jig for retaining cam timing in order to remove the valve cover.
P 256 = Fixture for securing cam shafts when valve cover is removed.
P 258 = Pins for locking cam shaft pulley & torque converter.
Not for Turbo Models.
SPECIAL ORDER ONLY !!!!
Delivery direct from the factory warehouse.
 $639.00
(Picture)
. . Clutch Tools .
3176
*
 Clutch Centering Mandrel. For Boxster.
See VW
.  . Cooling .
.
*
 . .
. . Crankshaft .
PORSCHE 9285/1 Used to remove crankshaft pully on type 911.
PORSCHE
9609
 Oil seal arbor used for the proper installation of oil seal on flywheel side of the crankshaft. Porsche 996 and Boxster. Special Order Only! Factory tool , Estimated cost $549.00 Call or eMail for Current Price.
Special Order
Only.
ST P251
*
 Oil seal arbor used for the installation of oil seal on the pulley side of the crankshaft. Trying to do this job with any other method could result in total engine failure by way of damaged oil seal.  Applicable to Porsche 996 and Boxster. Made by Sir Tools. 
.
.
 Cylinder Head .
KL-4031-3412
 * KLANN brand. Extra long XZN-M12 Socket. 1/2" drive. 200mm long. Useful on some Porsche engines.
PORSCHE
9633
 Cylinder head socket for 911/Boxster. 1/2" drive. Special size by HAZET Germany!
*Sale! Only one available at this price.
  
                       $49.99
. . Electrical Tools .
SW 1501+1511
*
 Stahlwille Kabelex pin release tool 1501 with a type 1511 bushing for round receptacles with locking tongue and contact size of 1.5mm. Outside diameter 3.3mm. This tool has an ingenious feature to protect the tip. A sliding cover is built into the handle. Also used on BMW, Mercedes, Fiat, Opel, and VW-Audi.
SW 1502 +1512
 * Stahlwille Kabelex pin release tool 1502 with a type 1512 bushing for round receptacles with locking tongue and contact size of 3.5mm. Outside Diameter 5.0 mm. $80.98
. . Engine .
PORSCHE
9206/1
 Flywheel lock for type 968. Used with engine installed in the car.

PORSCHE
9538/1
 Flywheel lock for type 968. Used with engine on a stand.
$ Price on Request
PORSCHE
VW 161a
 Snap ring pliers, very heavy duty, 190mm long, Made in Germany. All models. No Longer Available.

No Longer Available
KUKKO
125
VW204B
 Crankshaft Oil seal installing tool. For type 912. High quality German tool.
See VW Page
MT10-201
*
 Matra Flywheel Retainer, for 924, to hold flywheel on removed engine.
ST 215
*
 Sir Tool Flywheel Lock is needed to secure the crank shaft from rotating during R&R of motor. Used in conjunction with tool# P 201, where Flywheel Lock bolts into a machined channel. It is applicable on all Porsche and VW  Boxer-4 or Boxer-6 up to 3.0L. 
ST P201
*
 Engine Holding Fixture - (5 Arm) is designed to securely carry the entire weight of a fully dresses air-cooled twin turbo Boxer-6, w/o having to remove the flywheel. Shaft Diameter 60mm.
ST P201 Kit
*
 Professional engine stand consists of tool #'s P 201, 313, 215. Designed to bolt up to every Porsche and VW air-cooled Boxer motor ever produced, from Type 1 up to 3.6L.
ST P201 WR
*
 Porsche Engine Adaptor Ring
$ 165.95
ST P212
*
 Oil Seal Arbor is needed for the proper installation of oil seal on flywheel side of crank shaft. Applicable: All Porsche and VW Boxer-4 motors, excluding 914.
ST P214
*
 Chain Tensioner is crucial for securing tensioners in their retracted position during installation. This tool assist in keeping the chain timing correct during this procedure. Applicable: Model - 911 with factory tensioners. Excluding pressure-fed types. 
ST P215
*
 Oil seal arbor that is needed for the proper installation of oil seal on flywheel side of crankshaft. It is applicable on model- 911 All years 1965-1977.
ST P216
*
 Oil Seal Arbor is needed for the proper installation of oil seal on pulley side of crank shaft. Applicable: Model - 911, '89-'65.
BU9262/1
9262/1
 Alignment Pin for oil cooler housing.  Applicable: Model - 944
Due to sealing problems,  it is recommended to change the oil pressure relief valve to the one piece style.
ST P222
*
 Sir Tools Magnetic "V" 17mm  wrench. Used for securing the top engine bolts  from rotating during R&R of motor transmission.
ST P229
*
 Puller, for distributor drive gear, VW and Porsche air cooled boxer-4 motors that is needed for the proper extraction of the distributor drive gear from engine case.
ST P231
*
 Sir Tools Oil Seal Arbor is needed for the proper installation of the balance shaft oil seal. Applicable: Model - 944.
ST P232
9200
 Sir Tools Locking Bar is needed to properly secure the balance shaft sprocket from rotating during R&R of retaining bolt. Applicable: Porsche 944.
ST P233
9206
 Sir Tools Flywheel lock is used to stop the motor from rotating during R&R of the crank shaft bolt of the motor on Porsche 944.
ST P234
*
 Arbor Oil Seal is needed for the proper installation of oil seal on flywheel side of crank shaft. Applicable: Model - 911, '94-'78; 928, 944, 968.
ST P238
*
 Sir Tools Starter Bushing Puller - 6 Volt
ST P239
VW228b
 Sir Tools, For removing starter bushing and pilot bearing. type 911 and 914.
ST P240
*
 Dial Guage Holder is needed to properly measure crank shaft flywheel and pulley end play. Can also be universally used to check clearances and run-out. Used in conjunction with a dial indicator. Applicable: All Porsche and VW Boxer-4 motors
ST P241
*
 Spring Clips - (2) are needed for securing cam followers within crank case half during assembly. Applicable: All Porsche and VW Boxer-4 motors.
ST P254
*
 Engine support bar. This is a special service tool used for the removal and repair of tans-axle or the gear box. The two side posts bolt directly to the vehicle by bottom suspension bolts.  Good for Porsche model 996. Made by Sir Tools. 
. . Exhaust .
. . . .
.############ . Fuel .
ST P206
*
 Adjustment Driver Kit (3) piece specially designed tool kit needed to properly adjust the mechanical injection pump for performance or emission tuning. 
Stahlwille
10508
*
 Stahlwille special tool to adjust the CO mixture on the Porsche 928 with 4 valves.  Flexi-joint with 3mm hex bit. 360mm long. No longer listed by Stahlwille. These are now SOLD OUT and are No Longer Available!
$49.95
SOLD
OUT
Stahlwille
10507NKK-3
*

CO adjustment tool, with 3mm ball end hex tip, for K-Jetronic fuel injection. Ball ended hexagon drivers DRALL, for use on hexagon socket head screws, swivel angle up to 25º each side, Chrome Alloy Steel,
chrome plated, black tips. With 2 component handle. Overall length 400mm.
$25.58
. . Intake .
. . . .
. . Oil Service .
HAZET
2169
*
 Wrench, Oil filter, 74.4mm, 14 point, 3/8" drive, and 27mm outside hex dirve. For Mann and Knecht filters. Made of a special magnesium alloy metal casting. Please compare to your filter before ordering!


$ 42.40
HAZET
2169-1 
*
 Wrench, Oil Service, Porsche 911 up to 1989, and some Audi/VW Diesel cars. Made of a special magnesium alloy metal casting. 92mm with 15 flats. With 1/2" drive. Please compare to your filter before ordering!
HAZET
2567-16
*
 Socket, Transmission Oil Service, Porsche Boxter, Audi A4, A6. This socket is 1/2" drive XZN-16 bit with hole.
ST P236
*
 Special tool needed for the removal of the oil piston pressure relief valve from engine casing. Applicable on all VW & Porsche Boxer-4 motors.
ST P242
*
 Oil Service Line Wrench Set is a (4) piece set specifically assembled for R&R of Porsche oil lines. R&R of oil lines is accomplished by wrenches countering each other. Set Consist of DIN: 27, 30, 32, 36mm.
. . Oxygen Sensor .
Matador
3081-00-62
 *
 Matador Split Oxygen Sensor Socket 22mm.
See
Matador
Page
. . Pliers .
. . . .
. . Radio Tools .
. . . .
. . Spark Plug .
PORSCHE
999-571-054-02
 Spark Plug wrench "Klein" 16mm, for type 964. With special XZN 10 mm drive. Drive tool not included.  For a drive tool, see HAZET 8808-10 socket with 3/8" drive , on our HAZET page. click here.
HAZET
2505-2
*
 Socket, Spark Plug  3/8" dr Expanding Spark Plug Socket, 13/16" (20.8mm) . With a rubber insert to hold the plug. It is made with Chrome-Vanadium  steel and mat chrome  plated. Push the release pin and this socket will adjust from 137.5mm to 157.5mm to 197.5mm.  HAZET suggests you use a model 8816GK flex head ratchet with this socket to get the most benefit. Popular item for the 356.
. . Steering .
ST P221
*
 Special Tool used to adjust the rear toe-in. Model 911, 924, 944
ST P235
*
 Sir Tool Eccentric Adjuster for the camber on 911 C2 & C4
. . Suspension - Shocks .
KUKKO
128-TC
T10187
 Special ball joint tool for Porsche Cayenne and VW Touareg.  33mm jaw. 50mm working height. See top of page for web special price!
HAZET
2593-19
*
 Special Socket, with cut-out side, 19mm for strut removal. Used on some 928 Porsche.  Please measure your nut before ordering.
HAZET
2593-21
*
 Special Socket, with cut-out side, 21mm for strut removal. Used on some Porsche. No Longer Avaliable
See Matra 3186 on our VW page, Click Here.
$73.82
(Picture)
ST P210
*
 Pin Wrench Socket, Needed to remove the ball joint nut without damaging the nut. Designed with an outer reinforcement sleeve. 1/2" dr. For model 911 years'89-'65, 912, and 914
. . Tool Box Tools .
HAZET
450N/4
*
 Special set of Hazet 450N wrenches for your Porsche tool box. Shipping 1 pound. One of each:
  • Double Open End 8mm x 9mm , type 450N, 139mm long
  • Double Open End 10mm x 11mm , type 450N, 155.7mm long
  • Double Open End 12mm x 14mm , type 450N, 175mm long
  • Double Open End 17mm x 19mm , type 450N, 220.9mm long
This set is no longer available. The 12x14mm wrench is no longer in production.
.
. . Transmission .
HZ 985-17
 *
 Socket, Oil Service, VW, 17mm hex key, 1/2 drive, for gearbox.
$ 28.42
(Picture)
ST P223
*
 Synchro Engagement Kit is needed for the proper removal of synchro rings from the gear. Applicable: Model - 911 Turbo with 4 speed, '88-'76; 3rd & 4th gears. 
ST P224
*
 Synchro Engagement Kit is needed for the proper removal of synchro rings from the gear. Applicable: Model - 911 Turbo with 4 speed, '88-'76; 1st & 2nd gears. 
ST P225
*
 Synchro Engagement Kit is needed for the proper removal of synchro rings from the gear. Applicable: Model - 911, '86-'72; 3rd, 4th, 5th gears. 912, '71-'65; all gears. 914; all gears. 
ST P226
*
 Synchro Engagement Kit is needed for the proper removal of synchro rings from the gear. Applicable: Model - 911, '86-'72; 1st and 2nd gears.
$ 122.00
ST P252
*
 Special coned and splined oil seal remover used for the removal of gear box main oil seal. Barbed threads secures into the inner part of the oil seal without any damage to vehicle parts. Porsche models 996 & Boxster. Made by Sir Tools.  $ 109.00
Matra
3383
 * Double Sealing Ring Mandrel. Porsche Boxster final drive seal. Aso for double sealing ring in the transmission/differential of Audi A4 with O1V automatic transmission front wheel drive.  About 13" inches (330mm) long.

$74.50
(Picture)
PORSCHE
9619
 Adjustment tool for adjusting the shift cable when the cable is removed. Model 911/Boxster.
$ 12.99
PORSCHE
 9619/1
 Adjustment tool for adjusting the shift cable when the cable is removed. Green Plastic. For model 997/987.

$ 12.99
.
 . . .
. . Valve Tools .
10-204
 * Valve Stem Seal Press Tool. Supplied by VW.
HZ 2577
 *
 Valve Stem Seal Press tool. NO LONGER AVAILABLE.
 $57.33
(Picture)
HAZET
8501LG-3
*
 Special Hazet valve adjust socket for Porsche 924 Turbo *No longer available. Only 2 in stock.
ST P202 * Cam Socket. Used to secure the camshaft when adjusting valves on Model 911 years 1965-1980.
 $44.95
(Picture)
ST P203 * Crowfoot 46mm. Used to remove camshaft nut. Model 911 years 1965-1980.
 $73.50
(Picture)
ST P207
*
 Dial Gauge Holder - ("Z" Block) is needed for accurate adjustment of valves. Aluminum "Z" block dial gauge holder comes equipped with a 50mm dial indicator extension pin. Applicable: Model - 911, 930. For a dial gauge, see our Horex page. Click here.
ST P207-1
*
 Replacement Extension Pin - (50mm)
$ 8.00
ST P213
*
 Sir Tool .004 Feeler Gauge is needed for correct adjustment of valve clearance. Comes with its correct shape for the contour of your fingers.

ST P213B
*
 Sir Tool. Pack of five spare blades for Feeler Gauge.


ST P213B-Set
*
 Sir Tool Feeler Gauge Set. Includes: .004 Feeler Gauge and pack of 5 spare blades.
     
$13.50
ST P228 * Spring Loaded Valve Gauge displays valve spring height using pre-calibrated indicators stamped onto the outside surface of this tool. Crucial for accurate valve spring adjustment. Applicable: Model - 911. $ 59.95
(Picture)
ST P 7E
*
 Valve Spring Compressor -(Exhaust) is designed for "On-The-Car" R&R of exhaust valve springs w/o having to remove the motor or cylinder heads. Applicable: Model - 911, '89-'65.  On backorder until
January 2013.

ST P 7I
*
 This Valve Spring Compressor is designed for "On-The-Car" R&R of intake valve springs w/o having to remove the motor or cylinder heads. Applicable: Model - 911, '89-'65.  On backorder until
January 2013.

Matra
VW541/1A
 		* Matra Valve Spring Compressor is needed for R&R of valve spring or rocker arm. This compressor comes with a 33mm press piece, and a 20mm press piece. Job can be done with the cylinder head on or off the car. Used in conjunction with tool 2036 below. Applicable: VW/Audi 4 & 5 cylinder gasoline powered engines. Porsche model-924.

Includes two press pieces!

VW541/6
20mm in diameter
VW541/5
33mm in diameter


Matra
2036
 		* Matra Support Bridge is needed for removal and replacement of valve spring or rocker arm. This job can be done with the cylinder head on or off the car. Used in conjunction with tool VW541/1A. Applicable: VW/Audi 4 & 5 cylinder gasoline powered engines. Porsche model - 924. Please note:  This item will cause your order to ship by UPS Ground. If you are outside the 48 States, extra shipping charges will apply. Please email us before purchasing this item.

 

See VW Page
. . Water Pump .
. . . .
. . Wheels .
HAZET
6800-1000-01/5
9450 Spare
 Spare Safety shearing Pins, for the Porsche Torque Multiplier tool 9450.  Set of 5 spare pins. Made by HAZET of Germany. Special size for Porsche. Used for Carrera GT wheels.  Please Note: HAZET can still supply the shear pins, but the special tool 9450 is no longer available.  We do not know of a substitute for it. The spare pin set is in stock, ready to ship! Call if you need shipping by Next Day Air UPS.
.
  
$489.99





Wrench - Torque
Stahlwille
730/5
 * Torque Wrench, Rapid Adjustment 6-50Nm or 5-36 Ft.Lbs., 9x12 insert opening. Sliding scale. Length 315mm, 805g. Ratchet head and other inserts sold separately. See Stahlwille Page, click here.

See
Stahlwille
Page
Stahlwille
730/12		 * Torque Wrench, Rapid Adjustment 25-130Nm or 20-95 Ft.Lbs., 4x18 insert opening. Sliding scale. Length 410mm, 1100g. Ratchet head and other inserts sold separately. See Stahlwille Page, click here. See
Stahlwille
Page
To see a picture of the tool, click on the price.

.
HOME Quick Search SEARCH eMail Samstag How To Order TOP
Copyright © 1997-2013  Samstag Sales